search

Spectrum-controls 140 MPM 204 00sc Manual de usuario Pagina 55

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 66
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 54
Meter Proving Module
57
Health Status THealth Status T
Health Status THealth Status T
Health Status T
est (Concept)est (Concept)
est (Concept)est (Concept)
est (Concept)
1.1.
1.1.
1. In Concept, access the I/O configurator and ensure that the module description, slot location, and
register assignments are correct.
2.2.
2.2.
2. Use the controller status to verify that the module is recognized and reported as healthy. If you find an
asterisk in front of the module name, the rack does not recognize the module. To correct the problem,
see troubleshooting.
Register Operation TRegister Operation T
Register Operation TRegister Operation T
Register Operation T
estest
estest
est
1.1.
1.1.
1. Check the count rate in the input register for a signal indication. If status bit 14 (counter input state) is
set to 0 and status bit 4 (zero rate) is set to 1, no signal is indicated. See “
No Signal IndicationNo Signal Indication
No Signal IndicationNo Signal Indication
No Signal Indication”.
2.2.
2.2.
2. It is a good idea to ensure that the 4X register and the 3X+3 Status word are set up properly. As a quick
check, disable all ladder programming and set the 4X register to 0000 hex.
TT
TT
T
roubleshootingroubleshooting
roubleshootingroubleshooting
roubleshooting
Ready LED Does Not IlluminateReady LED Does Not Illuminate
Ready LED Does Not IlluminateReady LED Does Not Illuminate
Ready LED Does Not Illuminate
Possible CausesPossible Causes
Possible CausesPossible Causes
Possible Causes
The most probable reasons for the LED not illuminating are:
• The PLC system is not receiving power from its power supply.
• The module is located in a defective PLC rack slot.
• The module is defective.
CorrCorr
CorrCorr
Corr
ective ective
ective ective
ective
ActionAction
ActionAction
Action
1.1.
1.1.
1. Make sure that the PLC is receiving power.
2.2.
2.2.
2. Reinstall the module in the rack according to instructions in chapter 2, “Installation and Wiring.”
3.3.
3.3.
3. If the ready LED still does not illuminate, try it in another PLC rack slot.
4.4.
4.4.
4. If you are still unable to start the module, call your local distributor.
Vista de pagina 54
1 2 ... 50 51 52 53 54 55 56 57 58 59 60 ... 65 66

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Instrumentos de medición Spectrum-controls 140 MPM 204 00sc
Instrumentos de medición Spectrum-controls 140 EHC 204 00sc Manual de usuario   (81 paginas)
Instrumentos de medición Spectrum-controls 140 AUI 040 00sc Manual de usuario   (52 paginas)
Instrumentos de medición Spectrum-controls 140 ACI 051 00sc Manual de usuario   (57 paginas)
Instrumentos de medición Spectrum-controls 140 ACI 052 00sc Manual de usuario   (62 paginas)
  • Boots Argon audio Pypes-performance-exhaust Gimp Pfannenberg
  • Polycom Cajas De Interruptores En Serie Skil Ejercicios Combinados Inalámbricos Caliber Los titulares Sony Los componentes del chasis Ferplast Gradas de equipos AV
  • Microlab Solo 6C Sony HT-ST9 Casio EX-ZR20 D-Link DNR-326 Behringer Ultrabass BVT5500H
  • AEG T97689IH Manual de usuario Sony BDP-S1100 Manual de usuario Dodge Ram Power Wagon Instrucciones de operaciones Craftsman 315.277140 El manual del propietario Liebherr WKes 4552 GrandCru Manual de usuario