Spectrum-controls 1756sc-OF8H Series A Manual de usuario Pagina 23
- Pagina / 170
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 2: Installing And Wiring Your Module 9
removed, use the write-on label located on the side of the terminal blocks
to identify the module location and type.
Preventing
Electrostatic
Discharge
This module is sensitive to electrostatic discharge.
!
ATTENTION: Electrostatic discharge can damage integrated circuits or
semiconductors if you touch backplane connector pins. Follow these guidelines when
you handle the module:
· Touch a grounded object to discharge static potential
· Wear an approved wrist-strap grounding device
· Do not touch the backplane connector or connector pins
· Do not touch circuit components inside the module
· If available, use a static-safe work station
· When not in use, keep the module in its static-shield box
Removal and Insertion
Under Power
These modules are designed to be installed or removed while chassis
power is applied.
!
ATTENTION: When you insert or remove a module while backplane power is
applied, an electrical arc may occur. An electrical arc can cause personal injury or
property damage by:
· sending an erroneous signal to your system’s field devices causing unintended
machine motion or loss of process control.
· causing an explosion in a hazardous environment.
Repeated electrical arcing causes excessive wear to contacts on both the module and
its mating connectors. Worn contacts may create electrical resistance that can affect
module operation.
- Important Notes 3
- Table of Contents 5
- Table of Contents ix 9
- Terms & 12
- Abbreviations You 12
- Should Know 12
- Preface xiii 13
- Module Overview 15
- Chapter 1 15
- System Overview 17
- 4 ControlLogix 18
- Chapter 1: Module Overview 5 19
- 6 ControlLogix 20
- Power Requirements 21
- Using your module in 22
- Module Installation and 22
- Preventing 23
- Electrostatic 23
- Discharge 23
- Removal and Insertion 23
- Under Power 23
- Compliance to 24
- European Union 24
- Directives 24
- Wiring Your Module 26
- Preparing and Wiring 27
- Terminal Block Layout 28
- Wiring Inputs to the 28
- IF8H Module 28
- Wiring Outputs to the 30
- OF8H Module 30
- 18 ControlLogix 32
- Operation Within the 33
- ControlLogix System 33
- Chapter 3Chapter 3 33
- Chapter 3 33
- Direct Connections 34
- Module Operation 34
- Modules in a Local 35
- Requested Packet 35
- Interval (RPI) 35
- Modules in a Remote 36
- Listen-Only Mode 36
- Multiple Owners of 37
- Input Modules 37
- Configuration 38
- Changes in an Input 38
- Module with Multiple 38
- Chapter 4 39
- 26 ControlLogix 40
- Analog HART Modules 40
- 28 ControlLogix 42
- 30 ControlLogix 44
- Configuration Tags 45
- Overview 45
- 32 ControlLogix 46
- Input Tags Overview 48
- Output Tags 49
- (OF8H Only) 49
- 36 ControlLogix 50
- If8h0Configuration 52
- Table 5.1b 53
- 40 ControlLogix 54
- Table 5.1d 55
- 42 ControlLogix 56
- Amplitude 57
- 44 ControlLogix 58
- Table 5.3b 59
- 46 ControlLogix 60
- 1.) Select Controller Tags 61
- 3.) Select Monitor Tags 61
- Click on the tag name of the 62
- Configuration information is 62
- 1.) Highlight the value of 64
- 2.) Type in the valid new 64
- Of8h0Configuration 66
- Table 6.1b 67
- 54 ControlLogix 68
- Table 6.1d 69
- 56 ControlLogix 70
- Table 6.1f 71
- 58 ControlLogix 72
- Table 6.2b 73
- 60 ControlLogix 74
- Table 6.2d 75
- Table 6.3 75
- Use a pulldown menu 78
- Pulldown menu 78
- 66 ControlLogix 80
- 68 ControlLogix 82
- 70 ControlLogix 84
- 72 ControlLogix 86
- Table 7.1(Packet 0) 87
- 74 ControlLogix 88
- 76 ControlLogix 90
- 78 ControlLogix 92
- Get HART Device Information 94
- 82 ControlLogix 96
- HART Pass-Through Command 98
- 86 ControlLogix 100
- Analog HART Modules 100
- 88 ControlLogix 102
- 90 ControlLogix 104
- 92 ControlLogix 106
- 94 ControlLogix 108
- Short Frame Long Frame 109
- Master to slave 02 82 109
- Slave to master 06 86 109
- 96 ControlLogix 110
- 98 ControlLogix 112
- Programming Examples 113
- Chapter 8 113
- 100 ControlLogix 114
- Set Attribute All message: 116
- Module Reconfigure Message: 116
- 104 ControlLogix 118
- 106 ControlLogix 120
- 108 ControlLogix 122
- 110 ControlLogix 124
- 112 ControlLogix 126
- 114 ControlLogix 128
- 116 ControlLogix 130
- Figure 5.6a (Packed ASCII) 131
- 118 ControlLogix 132
- OK LED CAL LED Fault Status 133
- 122 ControlLogix 136
- 124 ControlLogix 138
- 126 ControlLogix 140
- 128 ControlLogix 142
- Maintaining Your Module 143
- And Ensuring Safety 143
- Chapter 10 143
- 132 ControlLogix 146
- HART Analog Modules 146
- Appendix A 147
- Environmental Conditions 148
- Regulatory Compliance 148
- Firmware Revision History 148
- Appendix B 149
- 140 ControlLogix 154
- 142 ControlLogix 156
- Appendix D 157
- 144 ControlLogix 158
- 146 ControlLogix 160
- 148 ControlLogix 162
- 150 ControlLogix 164
- 152 ControlLogix 166
- Table 3c (First Byte) 167
- Table 3d (Second Byte) 167
- 167
- 154 ControlLogix 168
- Getting Technical 169
- Assistance 169
- Declaration of 169
- Conformity 169
Relacionado con productos y manuales para Instrumentos de medición Spectrum-controls 1756sc-OF8H Series A
(118 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales