Spectrum-controls 1769sc-HART Modules Manual de usuario Pagina 100
- Pagina / 186
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Compact IO™ Isolated HART Analog Input Module
User's Manual 0300215-03 Rev. A
7-32
Table 7-11 (Response When Device Information Is Available)
HART Get Device Information - reply packet structure
Field Value Definition
HART Channel Number 0x00 – 0x03 (1 byte) Module input channel number for
HART command
Status 00 = SUCCESS Command status
Count (1 byte) Number of data bytes to following.
HART
ManufacturerIDCode
(1 byte) CMD#0, Byte 1
HARTDeviceTypeCode (1 byte) CMD#0, Byte 2
HARTPreamble (1 byte) CMD#0, Byte 3
HARTUnivCmdCode (1 byte) CMD#0, Byte 4
HARTTransSpecRev (1 byte) CMD#0, Byte 5
HARTSoftwareRevision (1 byte) CMD#0, Byte 6
HARTHardwareRevision (1 byte) CMD#0, Byte 7
HARTFlags (1 byte) CMD#0, Byte 8
Pad for 32 bit alignment (1 byte)
HARTDeviceIDNumber (3 bytes) Device ID
number
CMD#0, Bytes 9-11
Pad for 32 bit alignment (1 byte)
HARTTag (8 bytes unpacked
ASCII)
CMD#13, Bytes 0-5
HARTDescriptor (16 bytes unpacked
ASCII)
CMD#13, Bytes 6-17
HARTDate (3 bytes) CMD#13, Bytes 18-20
Pad for 32 bit alignment (1 byte)
HARTFinalAssemblyNum
ber
(3 bytes) CMD#16, Bytes 0-2
Pad for 32 bit alignment (1 byte)
HARTMessage (32 bytes unpacked
ASCII)
CMD#12, Bytes 0-23
HARTPVCode (1 byte) CMD#50, Bytes 0, 0xff if not supported
HARTSVCode (1 byte) CMD#50, Bytes 1, 0xff if not supported
HARTTVCode (1 byte) CMD#50, Bytes 2, 0xff if not supported
HARTQVCode (1 byte) CMD#50, Bytes 3, 0xff if not supported
HARTPVUnits (1 byte) CMD#3, Byte 4
HARTSVUnits (1 byte) CMD#3, Byte 9, 0 if not present
HARTTVUnits (1 byte) CMD#3, Byte 14, 0 if not present
HARTQVUnits (1 byte) CMD#3, Byte 19, 0 if not present
HARTSlot0Units (1 byte) CMD#33, Byte 1, 0 if not present
Output module use only.
HARTSlot1Units (1 byte) CMD#33, Byte 7, 0 if not present
Output module use only.
HARTSlot2Units (1 byte) CMD#33, Byte 13, 0 if not present
Output module use only.
HARTSlot3Units (1 byte) CMD#33, Byte 19, 0 if not present
Output module use only.
HARTPVLowerRange (4 bytes – Floating Point
Value)
CMD#15, Bytes 3-6
HARTPVUpperRange (4 bytes – Floating Point
Value)
CMD#15, Bytes 7-10
Pad for 32 bit alignment (3 bytes)
The command status, the second byte in the reply packet for the module specific
command, can return three different responses, SUCCESS, RUNNING and DEAD.
These responses echo the state of the module at the time the command is sent. The
conditions for each response are as follows:
SUCCESS will be sent back when all of the following conditions are met:
•
Command and HART Channel number are both valid.
- Compact™ I/O 1
- Isolated HART 1
- Analog Module 1
- Table of Contents 3
- Preface 7
- Conventions 8
- Used in This 8
- Chapter 1 9
- Module Overview 9
- Do No t Remov e RTB Un der 10
- Power Unless Area is Non 10
- Hazardous 10
- Section 1.5 11
- System 11
- Overview 11
- 1.5.1 System Operation 11
- Section 1.6 12
- Module 12
- Operation 12
- Chapter 2 13
- Quick Start for Experienced 13
- Chapter 3 19
- Installation and Wiring 19
- 3.3.3 Remove Power 21
- 3.3.4 Selecting a Location 21
- Section 3.4 22
- System Assembly 22
- Section 3.5 23
- Mounting 23
- 3.5.1 Minimum Spacing 23
- 3.5.2 Panel Mounting 23
- 3.5.3 DIN Rail Mounting 24
- 3.7.2 Terminal Door Label 26
- 3.7.5 Wiring the Module 27
- 3.7.6 Wiring Diagram 28
- 3.7.7 Calibration 28
- Chapter 4 29
- Configuring the IF4IH for 29
- CompactLogix Using 29
- RSLogix 5000 29
- Section 4.2 33
- The Add-On 33
- Profile 33
- Section 4.4 36
- Project Tags 36
- Project 38
- Chapter 5 41
- Configuring the IF4IH for a 41
- MicroLogix 1500 Using 41
- RSLogix 500 41
- Section 5.2 42
- Configuring 42
- 1500 System 42
- Section 5.3 46
- Using the 46
- Ladder Sample 46
- Chapter 6 51
- Module Data, Status, and 51
- Channel Configuration 51
- Section 6.4 55
- Configuration 55
- Raw/Proportional Data 62
- Engineering Units 62
- Scaled-for-PID 62
- Percent Range 62
- 6.4.9 Channel X 64
- 6.4.10 Channel X 64
- 6.5.8 Reserved (Words 24…45) 66
- Section 6.6 67
- Determining 67
- Effective 67
- Resolution 67
- Section 6.7 68
- Update Time 68
- Chapter 7 69
- Enabling and Using HART on 69
- Table 7-1 (HART Packet 0) 73
- Table 7-2 (HART Packet 1) 74
- Figure 7-4 (Packet Ladder) 77
- 7.2.3 Packet Interval 78
- Section 7.3 79
- Sending 79
- Messages 79
- 7.3.3 Processing a Message 81
- Figure 7-6 Sending Message 82
- Figure 7-8a (Message Ladder) 84
- Figure 7-8b 85
- Figure 7-8c 86
- Figure 7-8d 87
- Figure 7-8e 88
- Figure 7-8f 89
- Figure 7-8g 90
- Figure 7-8h 91
- Figure 7-8i 92
- Figure 7-8j 93
- Figure 7-8m 95
- Figure 7-8n 96
- Figure 7-8o 97
- Section 7.4 98
- Module Specific 98
- Commands 98
- Attention 103
- Figure 7-10b 107
- Figure 7-10c 108
- Figure 7-10d 109
- Figure 7-10e 110
- Section 7.5 111
- HART Protocol 111
- 7.5.1 Message Format 111
- Chapter 8 117
- Programming Examples 117
- Figure 8-4b 121
- 8.2.1 MAIN Routine 123
- 8.2.2 PACKETS Routine 124
- Figure 8-6b 125
- Figure 8-6c 126
- 8.2.3 MSG_TO_MOD Routine 127
- Figure 8-7b 128
- Figure 8-7c 129
- Figure 8-7d 130
- Figure 8-7e 131
- Figure 8-7f 132
- Figure 8-7g 133
- Figure 8-7h 134
- Figure 8-7i 135
- Figure 8-7j 136
- Figure 8-7k 137
- Figure 8-7l 138
- Figure 8-7m 139
- Figure 8-7n 140
- Figure 8-7o 141
- Figure 8-7p 142
- Figure 8-7q 143
- 8.2.4 SRC_CHECK Routine 144
- Figure 8-8b 145
- 8.2.5 DEST_CHECKSUM Routine 146
- Figure 8-9b 147
- 8.2.6 HART_MSG Routine 148
- Figure 8-10b 149
- Figure 8-10c 150
- Figure 8-10d 151
- Figure 8-10e 152
- Figure 8-10f 153
- Figure 8-10g 154
- Figure 8-10h 155
- Figure 8-10i 156
- Figure 8-10j 157
- Figure 8-10k 158
- 8.2.7 WORD_BYTE Routine 159
- Figure 8-11b 160
- Figure 8-11c 161
- 8.2.8 HART_CHECK Routine 162
- Figure 8-12b 163
- 8.2.9 BYTE_WORD Routine 164
- Figure 8-13b 165
- Chapter 9 167
- Diagnostics and 167
- Troubleshooting 167
- 1514131211109876543210 169
- 0000000000000000 169
- Value Bits 11 170
- Description 170
- Section 9.8 171
- Inhibit Function 171
- Appendix A 173
- Module Specifications 173
- Section A.2 174
- Environmental 174
- Specifications 174
- Appendix B 177
- HART Universal and Common 177
- Practice Commands 177
- Wire Size · 3-9 183
- Wiring Diagram · 3-10 183
- Wiring Guidlines · 2-3 183
- Getting Technical 185
- Assistance 185
- Declaration of 185
- Conformity 185
Relacionado con productos y manuales para Instrumentos de medición Spectrum-controls 1769sc-HART Modules
(176 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales