Spectrum-controls 1769sc-HART Modules Manual de usuario Pagina 55
- Pagina / 186
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Chapter 4: Module Data, Status, and Configuration
User's Manual 0300215-03 Rev. A
6-5
Section 6.4
Module
Configuration
After module installation, you must configure operation details, such as input type, data
format, etc., for each channel. Configuration data for the module is stored in the
controller configuration file, which is both readable and writable.
The default value of the configuration data is represented by zeros in the data file. The
structure of the channel configuration file is shown below.
Table 6-2a (Module Configuration)
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
0
Real Time Sample
1
ETS 0 EH3EH2EH1EH0
General Conf iguration
Bits
2
EC EA AL EI
Ch0 Filter Frequency an d
General Settings
3
Ch0 Data format and
input t ype
4
Ch0 Process Alarm High
Value
5
Ch0 Process Alarm Low
Value
6
Ch0 A larm Dead ba nd
7
Data Padding
8
EC EA AL EI
Ch1 Filter Frequency an d
General Settings
9
Ch1 Data format and
input t ype
10
Ch1 Process Alarm High
Value
11
Ch1 Process Alarm Low
Value
12
Ch1 A larm Dead ba nd
13
Data Padding
14
EC EA AL EI
Ch2 Filter Frequency an d
General Settings
15
Ch2 Data format and
input t ype
16
Ch2 Process Alarm High
Value
17
Ch2 Process Alarm Low
Value
18
Ch2 A larm Dead ba nd
19
Data Padding
20
EC EA AL EI
Ch3 Filter Frequency an d
General Settings
21
Ch3 Data format and
input t ype
22
Ch3 Process Alarm High
Value
23
Ch3 Process Alarm Low
Value
24
Ch3 A larm Dead ba nd
25
Data Padding
Function
Real Time Sample Value
Reserved Slot Variable (0-3) Input Filter Ch3
Reserved
Ch3 Data
Format
Reserved Ch3 Input Type
PA
Reserved Slot Variable (0-3) Input Filter Ch0
Handle Timeout
Word
Bit
Ch1 Input Type
Pad
Channel 0 High Process Alarm Setpoint
Channel 0 Low Process Alarm Setpoint
Channel 0 Alarm Deadband
Reserved
Ch0 Data
Format
Reserved Ch0 Input Type
Pad
Channel 1 High Process Alarm Setpoint
Channel 1 Low Process Alarm Setpoint
Channel 1 Alarm Deadband
Reserved Slot Variable (0-3) Input Filter Ch1
Reserved
Ch1 Data
Format
Reserved
Channel 2 High Process Alarm Setpoint
Channel 2 Low Process Alarm Setpoint
Channel 2 Alarm Deadband
Reserved Slot Variable (0-3) Input Filter Ch2
Reserved
Ch2 Data
Format
Reserved Ch2 Input Type
Pad
Pad
Channel 3 High Process Alarm Setpoint
Channel 3 Low Process Alarm Setpoint
Channel 3 Alarm Deadband
- Compact™ I/O 1
- Isolated HART 1
- Analog Module 1
- Table of Contents 3
- Preface 7
- Conventions 8
- Used in This 8
- Chapter 1 9
- Module Overview 9
- Do No t Remov e RTB Un der 10
- Power Unless Area is Non 10
- Hazardous 10
- Section 1.5 11
- System 11
- Overview 11
- 1.5.1 System Operation 11
- Section 1.6 12
- Module 12
- Operation 12
- Chapter 2 13
- Quick Start for Experienced 13
- Chapter 3 19
- Installation and Wiring 19
- 3.3.3 Remove Power 21
- 3.3.4 Selecting a Location 21
- Section 3.4 22
- System Assembly 22
- Section 3.5 23
- Mounting 23
- 3.5.1 Minimum Spacing 23
- 3.5.2 Panel Mounting 23
- 3.5.3 DIN Rail Mounting 24
- 3.7.2 Terminal Door Label 26
- 3.7.5 Wiring the Module 27
- 3.7.6 Wiring Diagram 28
- 3.7.7 Calibration 28
- Chapter 4 29
- Configuring the IF4IH for 29
- CompactLogix Using 29
- RSLogix 5000 29
- Section 4.2 33
- The Add-On 33
- Profile 33
- Section 4.4 36
- Project Tags 36
- Project 38
- Chapter 5 41
- Configuring the IF4IH for a 41
- MicroLogix 1500 Using 41
- RSLogix 500 41
- Section 5.2 42
- Configuring 42
- 1500 System 42
- Section 5.3 46
- Using the 46
- Ladder Sample 46
- Chapter 6 51
- Module Data, Status, and 51
- Channel Configuration 51
- Section 6.4 55
- Configuration 55
- Raw/Proportional Data 62
- Engineering Units 62
- Scaled-for-PID 62
- Percent Range 62
- 6.4.9 Channel X 64
- 6.4.10 Channel X 64
- 6.5.8 Reserved (Words 24…45) 66
- Section 6.6 67
- Determining 67
- Effective 67
- Resolution 67
- Section 6.7 68
- Update Time 68
- Chapter 7 69
- Enabling and Using HART on 69
- Table 7-1 (HART Packet 0) 73
- Table 7-2 (HART Packet 1) 74
- Figure 7-4 (Packet Ladder) 77
- 7.2.3 Packet Interval 78
- Section 7.3 79
- Sending 79
- Messages 79
- 7.3.3 Processing a Message 81
- Figure 7-6 Sending Message 82
- Figure 7-8a (Message Ladder) 84
- Figure 7-8b 85
- Figure 7-8c 86
- Figure 7-8d 87
- Figure 7-8e 88
- Figure 7-8f 89
- Figure 7-8g 90
- Figure 7-8h 91
- Figure 7-8i 92
- Figure 7-8j 93
- Figure 7-8m 95
- Figure 7-8n 96
- Figure 7-8o 97
- Section 7.4 98
- Module Specific 98
- Commands 98
- Attention 103
- Figure 7-10b 107
- Figure 7-10c 108
- Figure 7-10d 109
- Figure 7-10e 110
- Section 7.5 111
- HART Protocol 111
- 7.5.1 Message Format 111
- Chapter 8 117
- Programming Examples 117
- Figure 8-4b 121
- 8.2.1 MAIN Routine 123
- 8.2.2 PACKETS Routine 124
- Figure 8-6b 125
- Figure 8-6c 126
- 8.2.3 MSG_TO_MOD Routine 127
- Figure 8-7b 128
- Figure 8-7c 129
- Figure 8-7d 130
- Figure 8-7e 131
- Figure 8-7f 132
- Figure 8-7g 133
- Figure 8-7h 134
- Figure 8-7i 135
- Figure 8-7j 136
- Figure 8-7k 137
- Figure 8-7l 138
- Figure 8-7m 139
- Figure 8-7n 140
- Figure 8-7o 141
- Figure 8-7p 142
- Figure 8-7q 143
- 8.2.4 SRC_CHECK Routine 144
- Figure 8-8b 145
- 8.2.5 DEST_CHECKSUM Routine 146
- Figure 8-9b 147
- 8.2.6 HART_MSG Routine 148
- Figure 8-10b 149
- Figure 8-10c 150
- Figure 8-10d 151
- Figure 8-10e 152
- Figure 8-10f 153
- Figure 8-10g 154
- Figure 8-10h 155
- Figure 8-10i 156
- Figure 8-10j 157
- Figure 8-10k 158
- 8.2.7 WORD_BYTE Routine 159
- Figure 8-11b 160
- Figure 8-11c 161
- 8.2.8 HART_CHECK Routine 162
- Figure 8-12b 163
- 8.2.9 BYTE_WORD Routine 164
- Figure 8-13b 165
- Chapter 9 167
- Diagnostics and 167
- Troubleshooting 167
- 1514131211109876543210 169
- 0000000000000000 169
- Value Bits 11 170
- Description 170
- Section 9.8 171
- Inhibit Function 171
- Appendix A 173
- Module Specifications 173
- Section A.2 174
- Environmental 174
- Specifications 174
- Appendix B 177
- HART Universal and Common 177
- Practice Commands 177
- Wire Size · 3-9 183
- Wiring Diagram · 3-10 183
- Wiring Guidlines · 2-3 183
- Getting Technical 185
- Assistance 185
- Declaration of 185
- Conformity 185
Relacionado con productos y manuales para Instrumentos de medición Spectrum-controls 1769sc-HART Modules
(176 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales